Comprehensive analysis of several major problems with fax machines

The fax machine has already demonstrated its important mission in the user's office environment a few years ago. However, in the process of using, perhaps many users will encounter a lot of problems more or less. In order to help users who are new to the fax machine to use the fax machine as quickly as possible, I have contributed the most likely problems and solutions that I have collected. I hope that these contents will benefit the primary users of the fax machine. !
1. When sending a fax, why does the original often have skewed or even jammed?
When the original is in the process of transmission, it is not the problem that the transfer skew is the original or the original is stuck. You should check whether the two stick shafts of the paper drive part inside the fax machine are loose, because the two stick shafts will not produce enough paper. The pressure of the paper is prone to skew or even blockage. Therefore, if the two shafts are loose, the two shafts should be cleaned and adjusted immediately, so that the two shafts return to normal working condition; if the two shafts are not parallel, Transmission skew or even paper jams can also occur.
Therefore, before the document is conveyed, the position of the original guide plate must be properly adjusted, and the document to be conveyed is neatly placed on the guide sheet; in addition to the above factors, the obstacle on the paper conveying path is easily blocked. The normal transfer of the original, resulting in paper jam or jam, so in the event of a paper jam, you should remember to open the side panel cover of the fax machine in time to remove paper scraps or other obstacles on the paper transport path.
Fax machine 2. Why does the fax machine transmit multiple pages at a time?
Each multi-page transfer is a common and very common failure phenomenon. There are many possible causes of such failures. For example, once the transmission metal piece of the paper conveying portion is deformed, this failure occurs. If the transmission metal piece is found to be deformed, it should be adjusted immediately or even replaced with a new transmission metal piece; if the cover of the fax machine is not properly covered, it is easy to cause a failure of multiple pages per transfer.
Therefore, before sending a fax, you should first carefully check whether the cover of the fax machine has been covered. In addition to the above two reasons, the quality of the separation rubber sheet directly affects the correct transmission of the original, if the separation rubber sheet occurs. If it is damaged or has dirt on the surface, it should be replaced or cleaned with detergent.
3. Why can't the fax machine automatically input the original?
There are many factors that cause the fax machine to not automatically input the original. There are mainly the following aspects: first check if there is any obstacle blocking on the paper conveying path, if it is necessary to remove it immediately; secondly, check the various related aspects on the fax machine control panel. If the indicator light is working properly, if the “Fax” indicator is not lit, it indicates that the original position sensor or the original reading sensor of the fax machine is not working properly or even malfunctions. We should check and replace them in time.
The third possible factor is that the rubber sheet is damaged or the pressure is abnormal. We should also carry out timely inspection. The fourth cause may be caused by the metal spring piece and the conveying roller shaft in the paper conveying mechanism. Loose, so that the original manuscript can not produce enough pressure, if this is the case, you should look at whether the side cover of the fax machine has been covered, check whether the metal spring piece has been deformed or loses its elasticity, once it is not working properly, it should be immediately replace.
Another cause of malfunction of the fax machine is that there is a problem with the input portion of the original. For example, if the surface of the original being conveyed is too smooth, it is easy to cause slipping and the original cannot be automatically input. In this case, the original should be copied and then transferred. The piece can be used. If the thickness of the original is not enough, the original cannot be automatically input. Therefore, you must ensure that the thickness of the paper being conveyed is greater than 0.15 mm, and then the original being conveyed cannot be curled, otherwise the fax machine will not Automatically input the original.

Glass Metal Cabinets

These glass door Metal Cupboards mean glass Sliding Door Storage Cabinets and Swing Door Cabinets.The features of the glass doors offer a quick overview of the entire contents inside.
Made from high quality cold rolled steel sheet and tempered glass, silent sliding mechanism, glass door cabinets are ideal for offices and study rooms, or where you want to display the content to dust free.
Glass metal cupboards have low, mid height, and full height choices, 2 to 4 adjustable shelf boards.
When the cupboards reach, you will find 5 layer carton package to prevent the glass doors breaking in transport.
Browse Metal Drawers to find other office storage cabinets!

Metal Cabinet with Glass Doors,Unique Glass and Metal Cabinet,Steel Cabinet Glass Doors

LUOYANG SHIDIU IMPORT AND EXPORT CO., LTD , https://www.shidiu-cabinet.com

Posted on