First, the use of ink cartridges common sense:
1. Store the ink cartridges at room temperature, avoiding sunlight, strong light and heat.
2. Do not tear the outer packaging of the ink cartridge and the air hole seal before the ink cartridge is installed on the machine.
3. After the ink cartridge is unpacked, please install it on the printer as soon as possible. Otherwise, it may cause the ink cartridge to leak ink or not spray color.
4. For best results, please use it within six months of installing the cartridge.
Second, the factors related to the life of the ink cartridge:
In the process of using the color inkjet cartridge (here, the ink cartridge of the same body), pay attention to the balanced use of the three colors of red, yellow and blue. Do not print only the image that is more than one color, because only one color is used in the ink cartridge. Even if the other colors are not used up, the inkjet cartridge cannot be used any more. In general, the higher the resolution of the printed image, the more ink is used.
Third, the solution to common problems in the printing process:
If you encounter the above problems during the printing process, you should first perform a self-test. If there is a missing line in the self-test pattern, you need to clean the print head. Under normal circumstances, when the print head is cleaned and then self-tested, the pattern is free of missing lines.
If the self-test pattern is still broken after cleaning, please repeat this operation for 4~5 times. Under normal circumstances, the missing line of the self-test pattern will be reduced, which proves that the cleaning is effective and should be cleaned.
Normal printing cannot be achieved after continuous cleaning, indicating that there is less or no ink in the ink cartridge and the ink cartridge needs to be replaced.
Newly installed ink cartridges sometimes encounter self-test missing wires or a certain color can not be sprayed out. At this time, do not easily judge that the print head is clogged, most of which are caused by bumps and inverted storage during transportation, etc. Wash it. Under normal circumstances, if there is a small number of missing lines in the self-test pattern, if you do not print high-quality pictures (such as just printing Files), you can print normally without cleaning the print head.
Fourth, the factors affecting the effect of printing pictures:
1, the quality of the ink cartridges.
2, the choice of media: different brands of different texture of the paper, the printing effect is different (such as the white paper to print a more vivid color).
3. The clarity of the original picture.
4. The resolution selected when printing out.
5, the use of different software to print pictures, color saturation is different. How to judge whether it is blocked or broken? If there is no change in the position of the missing line in the pattern after each cleaning, the line is always missing at a fixed position, indicating that the nozzle is blocked. If the position of the missing line is changed, it is not a plug but a broken line. It is normal to have a wire break when replacing the ink cartridge (or after adding ink). Generally, the cleaning is good once or twice, and it is reduced every time the cleaning is broken (note: the cleaning time is preferably more than 10 minutes). There is a broken wire during use. If the more the wire is broken, the ink in the ink cartridge is gone. This is to replace the ink cartridge immediately. When using an inkjet printer, you should develop the habit of doing nozzle inspection frequently, especially for users who are not using it every day, to avoid the scrapping of prints caused by disconnection, so as to avoid unnecessary time and ink waste.
I hope that everyone can eliminate the bad habits and misunderstandings in the ink-filling behavior, improve the printing effect and reduce the cost of use.
First of all, the sponge in the ink cartridge has a certain life span. When the sponge repeatedly repeats the process of "absorbing-releasing" the ink or using it for more than a certain period of time, the ink absorption capacity of the sponge will be reduced, thus filling the ink cartridge into the ink cartridge. The ink will not be completely absorbed by the sponge, and the pressure of the ink in the ink cartridge on the nozzle portion will become large, causing the ink to flow out from the nozzle. This is why many people complain that the amount of ink printed is not as good as the original ink.
Secondly, between the ink cartridge and the ink inlet of the nozzle, a rubber sealing ring is used to ensure the sealing of the ink cartridge and the nozzle to ensure that the ink cannot leak out. Long-term use or multiple removal of the ink cartridge will cause the seal to age and the sealing effect will be deteriorated, causing the ink to ooze out from the joint. This will cause the ink to accumulate on the nozzle and mix, resulting in the color mixing of the bottom ink. The direct result is printing. When the artwork is discolored, you need to print multiple artwork to restore the color. This situation can also lead to waste of ink and an increase in the amount of waste ink from the printer.
Third, no matter how good the ink is filled, some impurities or dust are brought into the inside of the ink cartridge after multiple fillings. The dust will be carried to and adsorbed on the filter screen of the ink cartridge as the ink flows. As the dust increases, the filter screen of the ink cartridge will be clogged, causing the ink to flow poorly, causing problems such as disconnection during printing. If the filter is completely blocked, there may be problems such as failure to print.
Files
LA Files, Lever Arch File, PVC files
Eagle (Guangzhou) Technology Development Limited , https://www.eagle-factory.com