The use rate of printers in modern office is very high. The printer brings high color and high quality photos for everyone, but also brings a lot of trouble for everyone. After the printer has been used for a period of time, it will inevitably encounter problems with the ink cartridges. Most people are unaware of such problems. The following Xiao Bian came to tell everyone how to do the ink cartridges? What should I do if the cartridge nozzles are clogged?
What to do if the cartridge is dry?
What should I do if the printer cartridge is dry? When you use it again, you need to clean the printer cartridge first to prevent the print head from being blocked. Let's look at the cartridge cleaning method:
1, first carefully remove the printer's ink cartridges.
2. After removing the ink cartridge, find the nozzle of the ink cartridge.
3, and then prepare a pot of warm water, about the temperature of about 50-60 °C, the nozzle at the bottom of the cartridge into the water and soak for 5 minutes, be careful not to put the entire cartridge into the water.
4. After the operation, remove the ink cartridges and shake the cartridges properly. When no ink flows out from the nozzles, wipe them gently with a fine cotton cloth or napkin. At this time, do not wipe the nozzle directly, otherwise it will cause the nozzle to clog, affecting the effect of printing text.
5. Finally, put the cleaned cartridge in a ventilated place to dry it and reinstall it in the printer.
Matters needing attention: When you take the ink cartridge, be careful not to touch the circuit board, because the static electricity generated by the human body and the sweat on the hand can easily damage the circuit board and cause the ink cartridge to be scrapped. The time between the separation of the ink cartridge and the print head cannot be too long, because if the ink cartridge is only taken out and stored, the print head will cause dry blockage and even scrap.
What should I do if the cartridge nozzles are clogged?
Inkjet printers are different from the dry print media used in dot matrix printers and laser printers. The printing materials for color inkjet printers are: ink is wet. If your printer is not used for a long time, or if the environment is too dry, it will be There is a case where the dry state of the ink clogged the nozzle due to a large amount of moisture evaporating. In addition, if the same cartridge is filled with different brands of different types of ink, especially low-quality ink, it is also prone to deposits and plug the nozzle. Once the printer nozzle is blocked, then the printed documents, images, photographs, etc., appear to be missing, disconnected, abnormal colors, blurred writing, lack of color, etc., and the printer will simply fail to print. In case you need to clean the print head of the printer. The following cleaning methods can help you solve these problems.
Method One: A simple software tool to clean the nozzle (ie, clean the cartridge nozzle with a driver)
Note: If the printer nozzle clogging is not very serious, but the printing effect is poor, then do a simple cleaning job, you can use the software driver provided with the printer driver to clean it, almost every inkjet printer will be provided with ink cartridge cleaning tool. When cleaning, first place a plain paper for the printer.
Operation method: Click "Start" → "Settings" → "Printers and Faxes". Take canonip1880 as an example. Right-click on canonip1880 and select "Properties". In the popup's Properties window, select "Print Preference page" → "Maintenance" → "Clean". The interface of the cleaning cartridge can appear. Press OK to confirm that the printer automatically enters the status of the cleaning cartridge. The internal printer will emit an irregular mechanical noise and wait for the power light to be on. After the noise disappears, the process of cleaning the ink cartridge is completed. After cleaning, print a test page again to check the ink condition. If it is still not ideal, you can repeat the above operation (wash again).
Method two: Manual cleaning nozzle
Prepare a clean dish or dish like container, pour some in warm water and soak the cartridge heads in water for two to ten hours (depending on the degree of blocking).
Method of operation: Pour warm water or cleaning solution into the container. The height should be just soaked in the sprayer. Do not let the cleaning liquid contact the circuit board of the spray head. Let the nozzle continue to soak in the cleaning solution for about 1 hour, waiting for immersion. After the soaking is completed, remove the nozzle cartridge and let the nozzle face outwards, and then forcefully dry it (use the centrifugal force to throw out the remaining ink, and use a napkin to dry the ink thrown near the ink cartridge nozzle. If necessary, you can use the cleaning. Liquid soaking can also be replaced with alcohol, such as the need for internal cleaning of the ink cartridge, a thorough cleaning of the cartridge.
After cleaning the nozzle, it is best to put it in a dry and ventilated environment to let it dry naturally, or it can be blown dry with a fan to ensure that there is no residual cleaning fluid or moisture inside. Then you can install the ink cartridge back in the printer (make sure the print head is completely dry, otherwise it may burn the nozzle!). At this point, the cleaning process of the cartridge nozzle is completed, and a test page is printed after the cartridge is loaded. , compare the effect before and after.
Problems such as blocked printer nozzles, dry ink cartridges, etc., have added to the annoyance that people have experienced while enjoying high technology. After reading the above small series on the cartridges how to do? What should I do if the cartridge nozzles are clogged? After the introduction, I believe that all of these troubles should have answers, I hope the above article content will be helpful to everyone.
The brand is Doll legend. The products are SD size ball jointed dolls. The products include ball joint dolls about 50cm-68cm in size. They are made of high resin. And there are many types of products for you to choose from.
About the dolls, we also have many types of Ball Jointed Doll, Nude Doll Body , Doll Parts , BJD Wig , BJD Clothing, BJD Shoes , BJD Eyes , Other Accessories, Stock Items. If you are interested, please feel free to contact us.
Sd Size Doll,Sd Resin Doll,Sd Size Bjd,Doll Legend Sd Doll
Changchun Huadu Network Service Co., Ltd , https://www.legenddollbjd.com