The mahogany furniture is very expensive furniture, and it is also the master's hard work. The furniture made of precious wood is very heavy and very brittle. When carrying it, it is easy for one person to move, causing one side to land first, causing a heavy weight to be added instantly. On one leg, the furniture is deformed or even damaged.
The mahogany experts introduce different types of mahogany furniture, and the handling methods are also different. Here are a few rough introductions to the methods of handling mahogany furniture:
The first type: When handling a long strip, the two hands should be placed on the front and rear slabs, and should not be placed on the head plates at both ends. Because the headboard in ancient furniture is a weak part. Before the middle of the Ming Dynasty, there was no headboard for the high-altitude furniture. After the middle and late Ming Dynasty, the head plate was added. It was connected with the tooth plate with only one small cymbal. A long strip of money is worth a hundred pounds. Light wood is worth a lot. If it is cracked because it can't be moved, it will be matched if it is cracked. If it is matched, it will not be the original one, and the value will naturally decrease.
Second: When carrying the table, you can't move the fragile parts. If it is a stone table, it is best to move and stack it face down to lower its center of gravity.
The third type: When carrying the chair, the armrest cannot be moved, and the chair surface must be moved. Because the armrest is the weakest, the weight of the entire chair cannot be accommodated.
The fourth type: When carrying the cabinet, the door pin must be pinned, and the drawer should be locked. It is best to use the rope to “bound†first, and tie the two rings to protect the cabinet door and drawer of the furniture, so as to avoid tilting during handling. Take it out and break it. The person who moves the cabinet should stand on both sides, and the person on one side moves the top of the cabinet, and the person on the other side lifts the lower foot of the cabinet to tilt the cabinet to an angle of 45° to the ground. This is more labor-saving, easy to travel through, and relatively safe, it is an internal move.
The fifth type: When transporting the Arhat bed and the canopy bed, the screen, the shelf, etc. should be removed first, placed on the bed surface, and then bundled and then moved.
Therefore, it is recommended that two or four people move at the same time and at the same time, so as not to crash or smash.
Points to note when handling mahogany furniture:
First point: Try to find some soft ropes. The foam will bundle the mahogany furniture packaging. When handling or moving the furniture, be sure to handle it gently, remove all the removable wooden partitions and glass, reduce the weight and put They are packaged separately so that they are not damaged when transported.
Second point: Remove all adjustable wooden partitions and glass and pack them separately to ensure that the furniture will not be damaged during handling.
The third point: In order to avoid deformation, breakage, paint stripping, scratching and abrasion of the furniture during the handling process, please do not slide or drag the furniture on the ground.
Fourth point: Close and lock all the drawers and doors, cover them with a moving pad or blanket, and gently tie them.
Fifth point: Use fillers or foam to protect the corners, protrusions and handles of the furniture.
Sixth point: When transporting TV cabinets, cabinets, and other panel-type mahogany furniture that can be divided into several parts, please disassemble them to reduce weight and facilitate handling.
Seventh point: Avoid placing the furniture near the heat source or air conditioning tuyere after handling. Dramatic changes in temperature can cause damage to the exposed parts of mahogany furniture, and the use of humidifiers, fireplaces or small heaters can also cause changes in mahogany furniture. Avoid placing these items together.
To learn more about furniture, please pay attention to Xianghe Furniture City official website http://
Thermal Roll Paper
Thermal roll paper
Thermal paper is also called thermal fax paper, thermal recording paper, thermal Copy Paper, and thermal copy paper in Taiwan. Thermal paper is a kind of processed paper, and its manufacturing principle is to coat a layer of "heat sensitive paint" (heat sensitive color change layer) on high-quality base paper.
Although there are more than a dozen chemicals used in this color change layer, there are at least the following compounds: leuco dyes, the dyes are of a wide variety, the most commonly used are fluorescent compounds; the color developer accounts for less than 20%, and the commonly used are double Phenol, p-hydroxybenzoic acid; sensitizers account for less than 10%, which contains benzenesulfonic acid amide compounds; fillers account for less than 50%, commonly used calcium carbonate (fine particles); adhesives account for less than 10%, Such as polyvinyl acetate; stabilizers, such as dibenzoyl terephthalate; lubricants, etc.
Therefore, the process is difficult and the technical requirements are high.
Thermal paper is generally sold in the form of rolls, generally 80mm×Φ60mm, 57mm×Φ50mm and other specifications are the most common. The first number indicates the width of the paper roll, and the back is the diameter. The general error of the width of 1, 2mm will not affect the use, because Printers generally can`t print on the edge
Thermal Roll Paper,Thermal Paper,Thermal Printer Paper,Thermal Receipt Paper
Shijiazhuang Qiancen Industry Co.,ltd , https://www.yuyilang.com