In daily life, it is inevitable that you will encounter small problems such as the blockage of kitchen sewers . Don’t look at the problems. Once blocked, it will seriously affect daily life. It’s not so fun to cook a dish and go to the toilet. Please come to the people who are professionally dredging the sewers. People only give the most serious water dredging. The small pipes above are cleaned up at all, and the charges are not low. It is often one month after the dredging, and it is blocked. Let's take a look at the related issues of how to clear the kitchen sewers.
Steps to dredge the sewer:
Generally, the more serious blockage is blocked by the bottom of the main pipe, and the small pipes above are not particularly smooth, and need to be unblocked. But the most important thing is to first open the main pipe at the bottom.
1. Wear rubber gloves first, because the things we will do next will be very dirty and oily, and the edges of the wires and tubes are likely to scratch the skin on the hands. Wearing gloves is the best protection.
2, this household manual dredge is a relatively hard wire ring structure, the steel ring on the head is relatively sparse, the back is relatively dense. We first take the plastic tube from the position in step 1 out of the downpipe, and then pass the upper part of the tool to the lowermost main pipe. The beginning is generally better, and the spring tube is kept deep.
3, deep into a certain degree, you will find that the spring steel wire can no longer enter, how can you not do it, this is the location of the blockage, don't be impatient, if you have "pipeline" at home, you can pour half a bottle If you don't have a pipe, you can use the kitchen heavy oil cleaner instead. If you don't have it, you can use the detergent. This step is mainly based on chemical decomposition to break down the blockage in the pipe. This plug is generally bonded together by grease, so detergents also have a role.
4. After pouring the chemical, wait for 10-20 minutes, then pour a pot into the tube to roll the water. At this time, you will hear the sound of the pipe that was blocked.
5. At this time, two people are required to operate together. One person holds the spring wire and the other person shakes the back handle. After shaking a few times, the wire will continue to pass. It may not be very good to start at the beginning, take it easy, and shake it for a while.
6. After the passage, the wire springs are all inserted into the pipe, and one person shakes the handle at the pipe mouth. Shake for a while to make sure that the debris in the tube is broken. At this point, the main pipeline below is unobstructed.
7. Remove the tool from the pipe and pour a large amount of water to see if there is any blockage. If the water flow is not smooth or the speed is slow, you need to insert the tool and continue to shake the handle.
8, the following pipe is good, now we need to clean up the water pipe. Regardless of the leaking of the above pipeline, since it has already been touched, it is best to get it clean and dredge. Clean the middle plastic tube first, and the tube is easy to remove. After removing it, put it in the hot-washed detergent for 10 minutes, and the grease and debris inside will slowly separate.
9. When you are wearing this plastic tube, you should remove the above with the horizontal tube and the two return pipes. Twist the two parts and the tube can be removed. After unloading, take a closer look at the structure of the pipe, and the inside bends around a lot. Direct cleaning is not clean, we need to split a few pieces
10. After unloading, remove the two water-filled water buckets. This is completely unloaded. After unloading, carefully clean the debris inside the tube and run the tube in the hot water-washed detergent for 10-20 minutes.
11. Take out the soaked tubes, brush them with a brush, and combine them one by one. Note that there will be a rubber sleeve in the following parts. When you unload the tube, be careful to keep it when you put it in, or it will leak.
12. After all the installation, let go of the faucet to let the water flow for a while, and observe what is leaking. If it leaks, then unload it and check it. There are two reasons for water leakage: one is that the rubber sleeve is not installed, and the other is that the screwing position is slippery. You can wrap the raw material tape when you screw it, it will be a lot dense.
The above is the Xiaobian of the decoration home network for you to bring all the contents of the kitchen sewer, I believe that after reading this article, the small master has a basic understanding of the sewer cleaning problem, if you want to know more about decoration consultation, Please click to enter the decoration process section.
More related wonderful reading:
How to install the kitchen sewer and install the kitchen sewer precautions
How to do sewer dredging small skills get
Body And Hair Care,Hair And Body Care,Body Shop Hair Cream,Dream Hair And Body Care
Guangzhou cosmeceuticals daily chemicals PTY,.LTD. , https://www.gzcosmetics.com